ADS-B Cantenna

I recently needed a new antenna for my ADS-B receiver, so I built this simple antenna using a pop can, some spare wire, and an SMA connector. The 3D models and build instructions have been posed to Thingiverse if you want to build your own.

I actually built this a few weeks ago, published on Thingiverse June 11th, but only got around to writing up the full process today. This is my first real post after setting up a new CMS for my site.

Background

I have been running an ADS-B receiver for over a year reporting statistics to FlightAware using their Piaware software. Recent statistics for my station are published on FlightAware.

Recently, I noticed my statistics were lower than normal. After some debugging investigating antenna placement, noise, and software load, I found the connector on my antenna had worn and finally broke clean off when trying to reposition the antenna. I crimped a new connector and sure enough, my statistics returned to normal.

I took this as motivation to build a dedicated ADS-B antenna to replace the generic antenna.

Design

Living in an apartment, I decided my best solution is a window mount antenna. I researched a few designs online and settled on a vertical dipole built out of a pop can. The part of these designs I did not like was the antenna’s mounting, so I decided to design my own window mount.

Design’s Referenced

FlightAware Forum Post, by abcd5670
Hackaday Article, by Tom Nardi

Modeling

ADS-B cantenna window mount modeling in Fusion 360
ADS-B cantenna window mount modeling in Fusion 360

I started by modelling the window mount. This protects the sharp can edges and make the whole build look a bit nicer. A few print iterations were tried to find the best channel width as the first revisions were a little too tight.

After modeling the window mount, I still had some motivation and went ahead and modeled some jigs to help measure elements and find the can center during the build process.

I designed this antenna with 68.75mm (1090MHz quarter wavelength) elements. The element length is parameterized in all the models so this design can quickly be adapted for different frequencies.

Build

After modelling the mount and jigs, the build process was pretty straight forward. With an overnight print and about an hour of assembly, I was able to quickly deploy this antenna. The 3D models and instructions are posted on Thingiverse if you would like to build your own.

Saftey

3D printing, soldering, and cutting can cause injury. Wear safety goggles; proceed at your own risk.

3D Printing

The first step in this build was to print the parts I had modeled earlier.

The parts were designed to not need supports and to use simple shapes so the print settings remained pretty straight forward. I printed all the parts with PLA using 20% infill, 0.12mm layers, and a 0.4mm nozzle with a simple brim and no support. 0.2mm layers would be okay for a quicker print on these parts, but I wanted a smoother finish on the window mount as it would be mounted in a visible spot and I had time.

Preparing the SMA Connector

Once everything was printed, my first step to assemble the antenna was to assemble the SMA connector and vertical element.

ADS-B Cantenna SMA Preparation
ADS-B Cantenna SMA Preparation

I started with a female, PCB-mount SMA connector. I snipped off the corner posts and soldered on a solid core scrap of hookup wire to act as the vertical element. I kept the vertical long so I could cut to the right size using the jig I printed.

Cutting the ADS-B cantenna vertical element to length using a 3D printed jig.
Cutting the ADS-B cantenna vertical element to length using a 3D printed jig.

The vertical element cut was straight forward.

ADS-B cantenna vertical element fully prepared.
ADS-B cantenna vertical element fully prepared.

Preparing the Can

With the vertical element prepared, the next step was to prepare the can.

Drilling the Center Hole

I drilled a center hole just large enough to fit the SMA connector. The center hole jig was designed to guide a 1/8″ drill bit. I only used the jig to mark the center point by etching the bottom of the can by hand with the drill bit. Afterwards, I drilled the hole with a hand drill in steps to the final hole size.

Drilling the bottom of a can using a 3D printed jig.
Drilling the bottom of a can using a 3D printed jig.

Inserting the SMA Connector

After the can was cut, I inserted the SMA connector before placing the can in the cutting jig so I could index the can element at the top of the SMA connector base.

ADS-B cantenna in can cutting jig indexed to the SMA connector base.
ADS-B cantenna in can cutting jig indexed to the SMA connector base.

Cutting the Can

To cut the can, I started trying to cut the can directly in the jig, but quickly found it was going to be hard to get a clean cut in the jig. Instead, I only marked the can in the jig then cut along the line using a box cutter.

Marking the can before the cut.
Marking the can before the cut.
ADS-B cantenna prepared but not mounted.
ADS-B cantenna prepared but not mounted.

Mounting the Antenna

With the cantenna prepared, all that is left is to mount the can. Mounting was very straight forward. I inserted the can into the window mount, connected it to the receiver, then attached to my window using adhesive strips.

ADS-B antenna fully assembled in window mount.
ADS-B antenna fully assembled in window mount.
ADS-B antenna fully assembled and deployed.
ADS-B antenna fully assembled and deployed.

Performance

After going through the entire build process, I found the antenna at least on par — maybe marginally better — with the telescoping antenna I was using before. The boost was not as much as I hoped, but this antenna has more mounting options and the build was fun. After experimenting with a few different windows, I found my East window received the most activity.

With the ADS-B Cantenna, I was able to start seeing activity up to 60 miles away.
With the ADS-B Cantenna, I was able to start seeing activity up to 60 miles away.

Leave a Reply

Your email address will not be published. Required fields are marked *